Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Anderson Mill, TX
Chimney repair in Anderson Mill usually comes down to one of two findings: a cracked clay tile liner in a 1980s masonry fireplace, or a rusted-out prefab metal flue that’s been baking in Texas heat for 35 years. We see both constantly in the 78729 ZIP code. The good news is that most of these repairs are straightforward once you know what you’re looking at, and that’s exactly why we bring a camera into every flue we inspect. Call (855) 507-9184 if you suspect your fireplace isn’t venting the way it should.
Why Anderson Mill Homes Are Different
Anderson Mill’s housing stock was largely built between the mid-1970s and late 1980s, and that matters more than most homeowners realize. The fireplaces in these homes are almost always original equipment: either a masonry firebox with a clay tile liner or an early-generation prefab metal fireplace with a round metal flue. Both systems are now 30 to 50 years old. Clay tile liners crack. Prefab flues rust through from the inside, especially after years of condensation cycling against Central Texas’s temperature swings.
The climate compounds the problem. Anderson Mill gets maybe eight to twelve weeks of real fireplace weather, clustered between late November and February. The rest of the year, those chimneys sit idle through 100-plus-degree summers. Creosote left from last winter’s fires doesn’t just sit there, it cures into a hard, glassy layer that’s more difficult to remove and more flammable than fresh soot. Meanwhile, the live oaks and cedar in the neighborhood drop leaves and pollen into uncapped flues, and birds and squirrels find open chimneys an inviting place to nest when nothing’s moving inside them.
What this means practically: an Anderson Mill chimney that hasn’t been inspected since the previous heating season is not a chimney you should light a fire in. The first hard freeze triggers a wave of calls because homeowners finally light a fire and discover smoke rolling back into the living room. By then, the flue has been blocked or compromised for months. A pre-season check in October catches these problems early.
Styles & brands we work with
Our Main Anderson Mill Services
The two services Anderson Mill homeowners call us for most often are chimney sweeping and dryer vent cleaning. Each has its own detailed page, but here’s what matters for this area specifically.
Chimney Sweep in Anderson Mill
A chimney sweep in Anderson Mill means more than brushing soot out of a flue. Given the age of the fireplaces in this area, every sweep we perform includes a camera inspection of the entire flue, because a clean chimney with a cracked liner is still a dangerous chimney. We remove creosote that’s often hardened from months of summer heat, clear out bird and squirrel nests, and check the firebox, damper, and chimney cap. If you haven’t had your fireplace looked at since last winter, this is the place to start. Chimney Sweep in Anderson Mill covers the full process and what to expect.
Dryer Vent Cleaning in Anderson Mill
Anderson Mill’s older homes often have long, multi-bend dryer vent runs that snake from a laundry room in the center of the house up through the attic and out the roof. Those runs collect lint fast, especially with the humidity we get in spring and early summer. A clogged dryer vent is a fire hazard and makes your dryer run longer on every load. We clean dryer vents with the same inspection-first approach we use on chimneys, and we’ll show you what we pulled out. Dryer Vent Cleaning in Anderson Mill has the details.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Chimney Repair in Anderson Mill
Chimney repair in Anderson Mill almost always traces back to age plus heat. Homes built in the 1970s and 1980s have original fireplaces that were never designed to last four decades without maintenance, and the long Central Texas summers bake whatever moisture sits inside the flue. The most common repair calls we answer are for cracked clay tile liners, rusted prefab flues, leaking flashing, and deteriorated chimney crowns. If you hear crumbling sounds when you open the damper or see staining around your fireplace, the fix is usually more straightforward than a full rebuild. Chimney Repair is a service we perform with professional-grade materials, named so you know exactly what’s being installed.
Chimney Cap Installation
Signs you need it
Birds or squirrels in the flue, visible rust or missing sections on your existing cap, or rainwater and leaves getting inside the chimney are all signs a cap needs to be installed or replaced.
What it costs in Anderson Mill
Chimney cap installation in Anderson Mill runs $350 to $750, depending on the cap style and flue size.
How we do it
We measure the flue opening, cut and install a stainless or galvanized cap sized to fit, and secure it to the flue with mechanical fasteners, then check draft to confirm airflow isn’t restricted.
Chimney Liner Installation
Signs you need it
Evidence of a cracked clay liner during camera inspection, visible pieces of tile in the firebox, smoke smell upstairs, or water staining on the chimney breast are signs the liner has failed.
What it costs in Anderson Mill
Liner installation in Anderson Mill starts around $2,800 and can run to $6,500, depending on the fuel type, flue length, and whether the chimney is straight or has offsets.
How we do it
We measure the flue precisely, pull a properly sized DuraFlex stainless liner through the chimney, insulate if the application calls for it, and terminate it with a cap designed for your fuel type.
Chimney Flashing Repair
Signs you need it
Water staining on the ceiling near the chimney, damp drywall around the firebox, or rust and separation in the metal where the chimney meets the roofline indicate the flashing is done.
What it costs in Anderson Mill
Flashing repair in Anderson Mill costs between $400 and $900, depending on access and the extent of the existing flashing damage.
How we do it
We remove failed flashing and old sealant, install new step and counter flashing in galvanized or stainless steel, and seal the termination point with a weather-rated sealant, then test for leaks.
Chimney Crown Repair
Signs you need it
A cracked, spalled, or missing chimney crown lets water run straight into the masonry below, and here the frequent freeze-thaw between cold fronts and hot days breaks ordinary crown patching apart.
What it costs in Anderson Mill
Crown repair in Anderson Mill typically falls between $450 and $950, depending on the crown’s condition and whether the old surface needs to be fully removed.
How we do it
We clean and prep the crown surface, build a proper concrete or polymer-modified crown with a slight slope for runoff, and form an expansion gap between the crown and flue that allows the liner to move independently.
What Chimney Repair Costs in Anderson Mill
| Item | Typical range in Anderson Mill |
|---|---|
| Chimney cap installation | $350 – $750 |
| Chimney flashing repair | $400 – $900 |
| Chimney crown repair | $450 – $950 |
| Chimney liner installation | $2,800 – $6,500 |
How long does chimney repair take in Anderson Mill?
Most cap, flashing, and crown repairs finish in a single visit of two to four hours. A full liner installation usually takes one day, occasionally two if the flue has tight offsets or requires extra mechanical work to remove old tile sections.
Can my cracked liner be fixed without full replacement?
In many Anderson Mill chimneys, yes. We’re HeatShield-certified, which means we can resurface a damaged flue with a manufacturer-rated coating instead of defaulting to full liner replacement. We’ll tell you plainly which path is appropriate after a camera inspection. Call (855) 507-9184 for an exact quote.
Brands We Service in Anderson Mill
We install and service professional-grade brands like Olympia Chimney, DuraFlex, Famco, and Copperfield. We name the products we install so you know exactly what’s going into your home, and we keep common parts in local inventory so typical Anderson Mill repairs don’t sit waiting on a shipment. Our brands explains why these matter.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Anderson Mill, TX
| Service | Typical range in Anderson Mill |
|---|---|
| Chimney sweep (standard cleaning and inspection) | $200 – $350 |
| Dryer vent cleaning | $150 – $300 |
| Chimney cap installation | $350 – $750 |
| Chimney cap replacement | $350 – $750 |
| Chimney flashing repair | $400 – $900 |
| Chimney crown repair | $450 – $950 |
| Chimney liner installation | $2,800 – $6,500 |
What pushes a chimney repair price up in Anderson Mill is access: steep roof pitches on two-story homes, flues with tight offsets, or a firebox that’s been buried behind drywall from a 1990s remodel all add time. What doesn’t change is the upfront price, because we quote every job before work starts and the number we give you is the number you’ll pay.
Neighborhoods We Serve in Anderson Mill
Ashton Chimney has served Anderson Mill since 2014, and we work throughout the 78729 area. Response time for most Anderson Mill jobs runs two to five business days for scheduled work, and we route existing customers first when winter demand spikes.
- Anderson Mill West
- Village at Anderson Mill
- North Oaks
- Oak View Estates
- Spicewood at Balcones
Service Area – Cities Near Anderson Mill
Ashton Chimney is based in nearby Cedar Park and regularly works across the surrounding communities. If you’re in Jollyville, TX, Brushy Creek, TX, Cedar Park, TX, or Wells Branch, TX, you’re inside our service area and we can schedule the same week in most cases.
Serving Anderson Mill, TX — Our Local Coverage Area
We’re based in the Anderson Mill area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Anderson Mill
Most scheduled sweeps and inspections in Anderson Mill can be booked within two to five business days. During the first cold snap in October or November, existing customers with prior service history get priority routing, so a pre-season booking is the better plan.
Most chimney repairs and sweeps in Anderson Mill do not require a permit, since they’re maintenance or replacement work on an existing system. If your repair involves a full liner replacement or structural work, we’ll handle the specifics with the local jurisdiction and tell you exactly what’s needed before anything starts.
Yes. We regularly do pre-purchase chimney inspections for homes in Anderson Mill’s 1970s and 1980s housing stock, and the camera goes in the flue every time. We’ll tell you what we found, what it means, and what your options are. Call (855) 507-9184 to schedule.
Ashton Chimney has served Anderson Mill since 2014. Call (855) 507-9184 for a free estimate on any chimney or dryer vent work in the 78729 area.
What happens when you call
- 1A real person answersNo phone trees — talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Anderson Mill Customers Say
"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
— Dustin Whitaker"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."
— Cole Doyle"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
— Tyrone Ingram